News Details
Epoxy resin fabric paint crosslinking agent
2017-7-12 23:12:00
Epoxy resin fabric paint crosslinking agent
Use enough epoxy resin to saturate the fabric and the wood below. After a few minutes, dry (white) area with additional epoxy resin. If the epoxy resin looks like milk in high humidity, it can be used to warm the surface with a hot gun or on the surface. Use low heat to remove air bubbles. Using the 207 crosslinking agent will certainly be completed successfully.
Epoxy resin coating barrier coatings are designed to provide an effective moisture barrier and a smooth foundation to enhance the epoxy coating. For an effective wet barrier, coat the least 2 layers of WESTSYSTEM epoxy. If you want to hit the sand, you can apply 3 layers of paint. Wet protection will add additional coating to the layer until the 6 - layer coating or about 20 thick ear thickness. Additives or pigments should not be added to the first coating.
There is no recommended diluent with WESTSYSTEM epoxy. Can be arbitrary processing, dilute amino foam roller, such as using WESTSYSTEM800 drum, allows you greater control of thickness of the film, it is more thick than using roller coating is less likely to cause epoxy resin exothermic and allow smaller score.
Cutting the coating to a narrower width is harder to achieve or more suitable for narrow narrow surfaces. Complete all refurbishing and application fabrics should be done before the final coating. The surface temperature of the porous surface is allowed to stabilize before coating. Otherwise, when the material is crosslinked, the air in the porous material expands from the material and causes the crosslinked coating to bubbly.
Mixed resins and 207 crosslinking agents, you can use it during operation time. Pour the mixture into a pan and mix it thoroughly. Make the drum load moderate amount of epoxy resin mixture. The rolling roller gets a uniform coating on the slant of the pan.
Gently and randomly, roll over an approximate 2ft area and evenly transfer the epoxy resin to the 2ft area. When the drum is dry, add enough pressure to spread the epoxy resin, further making the film thinner. Increasing the area will make the membrane thinner and spread evenly.
Chinese name: Diethyl toluene diamine(DETDA)Diethyltoluenediamine packingļ¼ net weight 200KG/ galvanized iron drum (a small cabinet pallet loaded 16 tons), 1000KG/IB barrels (a small cabinet loaded 18 tons or 23 tons of ISOTANK).
Thinner film, it is easier to cover and avoid the drop of each coating. Finish the area with long, light and reduced roller stroke. Early coating areas overlap by mixing to make them all. The area coating of these small work, you can achieve with each batch. If a batch starts to thicken, before it can be used, discard it and mix fresh ingredients in or use smaller batches.
Gently drag a foam roller brush on fresh epoxy resin to elongate the coating and even use it in subsequent overlap. Use enough pressure to make a smooth surface, but this does not remove any coating. In this area, the drag of each direction alternately, the first coating of the longitudinal, the second coat of the horizontal, the third coating of the longitudinal, etc. The surface of the WESTSYSTEM800 drum can be cut into pieces.
Apply the following process to epoxy resin. Ensure that the previous coating is fully connected and supports the weight of the next coating. In order to avoid sand between the coatings, use all of the coating in the same time to prepare the sedate preparation - Curedepoxy.
After finishing the final coating overnight, wash and sand it to prepare for the final work. The final surface preparation of appropriate completion technology is not only the efforts to achieve your wishes to add beautiful to your work, but also will protect your face resistance to ultraviolet radiation, prevent future flake epoxy resin under the irradiation of ultraviolet light.
The most common method is to paint the finished surface with uv light. A coating system with uv radiation is prepared in advance. Final preparation is as important as repainting epoxy resin. First, the surface must be clean, dry and sanding.
Copyright: Zhang Jia Gang YaRui Chemical co.,Ltd
Copyright: Zhang Jia Gang YaRui Chemical co.,Ltd
Spanish
French
Italian
Portuguese
Japanese
Korean
Arabic
Russian